Search found 434 matches
| Author | Message |
|---|---|
| Topic: major whallop with blade hybrid. | |
| glyn485 Replies: 1 Views: 29 |
 Forum: E-Flite Blade 400, CX, mCX CX II, CX III and others. Posted: Sat Mar 20, 2010 11:48 am Subject: major whallop with blade hybrid. |
| Hi guys, well after a good week of flying and managing to get out a few times through the week, decided to call at my local field on way home from work, had fitted a new hybrid head to the blade last ... | |
| Topic: Some help needed with hk450 setup PLEASE | |
| glyn485 Replies: 35 Views: 258 |
Forum: Other Clone helicopters Posted: Sat Mar 20, 2010 10:59 am Subject: Some help needed with hk450 setup PLEASE |
| Hi Dale, just re-read you post about the swash not traveling all way up shaft, the swash mix is set around 60% as this figure gives you roughly 10% of pitch, both neg' & pos'. You don't want the ... | |
| Topic: Some help needed with hk450 setup PLEASE | |
| glyn485 Replies: 35 Views: 258 |
Forum: Other Clone helicopters Posted: Sat Mar 20, 2010 10:39 am Subject: Some help needed with hk450 setup PLEASE |
| Hi Dale start off @ 60 swash mix settings, don't know what you mean by 'travelling the full length of the shaft'.....Glyn | |
| Topic: Some help needed with hk450 setup PLEASE | |
| glyn485 Replies: 35 Views: 258 |
Forum: Other Clone helicopters Posted: Fri Mar 19, 2010 9:33 pm Subject: Some help needed with hk450 setup PLEASE |
| No probs Dale , if I can help here goes, firstly set the idle up pitch curve in tx from 0-100 and the throttle in idle up @ 90- 90. now remove blades and disconnect the motor, get yourself two nails ... | |
| Topic: acer-lab gyro | |
| glyn485 Replies: 3 Views: 57 |
Forum: Gyros Posted: Fri Mar 19, 2010 8:02 pm Subject: acer-lab gyro |
| mine does...Glyn | |
| Topic: Some help needed with hk450 setup PLEASE | |
| glyn485 Replies: 35 Views: 258 |
Forum: Other Clone helicopters Posted: Fri Mar 19, 2010 6:29 pm Subject: Some help needed with hk450 setup PLEASE |
| Hi Dale, not sure about this info but I would try setting the trim all the way down and throttle wide open then couple heli to lipo, when it beeps then move throttle to low position, I would guess thi ... | |
| Topic: Black Angel & AE V2 Combo | |
| glyn485 Replies: 2 Views: 95 |
Forum: Copter-X Clone and other Copter X variants. Posted: Fri Mar 19, 2010 5:50 pm Subject: Re: Black Angel & AE V2 Combo |
| £131 + Shipping. This is a corking deal and I couldn't resist. Easter Sale, the usual eH HK site.....
Going to build the AE as a cheap 'trainer' with a list of parts that I have lifted from anoth ... |
|
| Topic: brand new broken dx6i | |
| glyn485 Replies: 21 Views: 155 |
Forum: Radio Transmitters. Posted: Fri Mar 19, 2010 5:46 pm Subject: brand new broken dx6i |
| Hi Dal, do you wanna go halves in a lottery ticket, good result mate, pleased for ya.....Glyn | |
| Topic: brand new broken dx6i | |
| glyn485 Replies: 21 Views: 155 |
Forum: Radio Transmitters. Posted: Thu Mar 18, 2010 5:32 pm Subject: brand new broken dx6i |
| no Dal, horizon are the main agent for spectrum in the uk, give them a call they can be very helpful, explain what happened and see what they say, you could get lucky....Glyn | |
| Topic: brand new broken dx6i | |
| glyn485 Replies: 21 Views: 155 |
Forum: Radio Transmitters. Posted: Thu Mar 18, 2010 5:17 pm Subject: brand new broken dx6i |
| Hi Dal, any contents insurance on the new place yet? just a thought....Glyn | |
| Topic: hk450 tail wag problem. | |
| glyn485 Replies: 16 Views: 128 |
Forum: Other Clone helicopters Posted: Thu Mar 18, 2010 8:28 am Subject: hk450 tail wag problem. |
| Hi Dal, go into your pitch curve menu and your throttle curve menu and tweak with these, try upping the headspeed a little or giving it a bit more pitch or whatever, thats why you have the dx6i so tha ... | |
| Topic: blade 400 hybrid | |
| glyn485 Replies: 5 Views: 79 |
Forum: Other Clone helicopters Posted: Wed Mar 17, 2010 7:49 pm Subject: blade 400 hybrid |
| Hi 10 russ, you're right, hadn't noticed that before you pointed it out, I have run the clones that way when I was learning but thought all my fleet were standard rotation now, don't seem to make any ... | |
| Topic: 450 or 250 | |
| glyn485 Replies: 7 Views: 145 |
Forum: T Rex 250, variants, upgrades and mods. Posted: Wed Mar 17, 2010 7:34 pm Subject: 450 or 250 |
| 450 first, 250 takes a little more experience IMO.....Glyn | |
| Topic: blade 400 hybrid | |
| glyn485 Replies: 5 Views: 79 |
Forum: Other Clone helicopters Posted: Tue Mar 16, 2010 8:47 pm Subject: blade 400 hybrid |
| Well guys, as I said I took the blade back out this afternoon, started doing steady 8's and circuits, getting braver and braver, bigger flight path and more sky etc, flew lovely then out of the blue g ... | |
| Topic: Tail pitch slider drag on new CX-SEv2 | |
| glyn485 Replies: 19 Views: 218 |
Forum: Copter-X Clone and other Copter X variants. Posted: Tue Mar 16, 2010 3:08 pm Subject: Tail pitch slider drag on new CX-SEv2 |
| Hi fast, welcome, remove the tail rotor hub and spin the heli up, without the blades, then a piece of fine carborundum paper between finger and thumb and run it down the tailshaft a few times, till al ... | |
| Topic: HK450 No power to anything Please HELP!!!!!!!!!!!! | |
| glyn485 Replies: 34 Views: 236 |
Forum: Other Clone helicopters Posted: Tue Mar 16, 2010 2:23 pm Subject: HK450 No power to anything Please HELP!!!!!!!!!!!! |
| Hi Dale, simple enough----red and black wires from ubec, solder to red and black esc imput on deans side, wherever you can, I removed a bit of the heatshrink on the esc and piggybacked on to the main ... | |
| Topic: blade 400 hybrid | |
| glyn485 Replies: 5 Views: 79 |
Forum: Other Clone helicopters Posted: Tue Mar 16, 2010 8:21 am Subject: blade 400 hybrid |
| Hi guys, just finished fitting the ally, protech zoom head to the blade, a lovely piece of engineering, got it from mrs bruce who flys in the clone section, took it out this morning for a test fly, ju ... | |
| Topic: HK450 No power to anything Please HELP!!!!!!!!!!!! | |
| glyn485 Replies: 34 Views: 236 |
Forum: Other Clone helicopters Posted: Mon Mar 15, 2010 9:51 pm Subject: HK450 No power to anything Please HELP!!!!!!!!!!!! |
| Hi Dale, try the hobby shop in Nottingham if you are close, if not then there's gliders at Newark, failing that then the giant fish post out very quick....Glyn | |
| Topic: Soon to join the copter x club | |
| glyn485 Replies: 9 Views: 144 |
Forum: Copter-X Clone and other Copter X variants. Posted: Mon Mar 15, 2010 9:04 pm Subject: Soon to join the copter x club |
| Hi dom and welcome to the pro club, a good step up from the k2, you won't be dissapointed, don't use the red loktite, get some blue. There's a build thread on here by Rhippy, the servo's are fine for ... | |
| Topic: HK450 No power to anything Please HELP!!!!!!!!!!!! | |
| glyn485 Replies: 34 Views: 236 |
Forum: Other Clone helicopters Posted: Mon Mar 15, 2010 8:54 pm Subject: HK450 No power to anything Please HELP!!!!!!!!!!!! |
| Hi Dale, as Friskle says, do you have the wire from the esc to the rx plugged in to the throttle port and is it the right way around, dont worry about turning it as it can't be damaged by doing so, al ... | |
| Topic: Am I Going Mad?? | |
| glyn485 Replies: 16 Views: 160 |
Forum: Copter-X Clone and other Copter X variants. Posted: Sun Mar 14, 2010 8:55 pm Subject: Am I Going Mad?? |
| Hi Loudy, no probs, glad I could help......Glyn | |
| Topic: metal upgade installed | |
| glyn485 Replies: 10 Views: 193 |
Forum: Belt CP V2, mods, upgrades and older models. Posted: Sun Mar 14, 2010 3:48 pm Subject: metal upgade installed |
| My guess is that you have put the tail on in reverse, ie twisted belt and reversed blades. I have run them in the past like this and found no problem, it's up to you, leave it or change it....Glyn | |
| Topic: For all those who've switched to 2.4 gig! | |
| glyn485 Replies: 5 Views: 107 |
Forum: T Rex 250, variants, upgrades and mods. Posted: Sun Mar 14, 2010 3:42 pm Subject: For all those who've switched to 2.4 gig! |
| yea but you'll not be so smug when you poke yourself in the eye with the long pointy aerial thingy.......Glyn | |
| Topic: Am I Going Mad?? | |
| glyn485 Replies: 16 Views: 160 |
Forum: Copter-X Clone and other Copter X variants. Posted: Sat Mar 13, 2010 9:35 pm Subject: Am I Going Mad?? |
| Hi Loudy, would imagine that you have sussed it, you had the foresight to know that something was wrong in your OP, got to agree with you , if it don't look right, it probably isn't right, give it a t ... | |
| Topic: Am I Going Mad?? | |
| glyn485 Replies: 16 Views: 160 |
Forum: Copter-X Clone and other Copter X variants. Posted: Sat Mar 13, 2010 3:48 pm Subject: Am I Going Mad?? |
| Hi, you changed the blade holder, not sure on the tail ATM but which side are your balls on the grips, leading or following......Glyn | |
